009.08.Board Bringup. Paspberry Pi4

pravjot

Issues, queries, suggestions or discussion related to

009.08.Board Bringup. Paspberry Pi4

should be posted here.

prashantmuniv

Can i use these commands for Raspberry Pi 3 Board Bringup?

niranjan

Hi

Setup for RaspberryPi

kernel Compilation and build module successfully completed on ubuntu host machine.

DEPMOD /home/niranjan/project/02.RaspberryPi/source/build_modules/lib/modules/6.6.28-v8+

setup and bringup beagle bone black

I have worked bring up activity on Beagle bone black board and completion work activity as below-

Build the kernel version 6.1.80 and deploy boot & roofs on SD card
board successfully boot from SD card and get console over ttyUSB0
xfce4 GUI installed and tested on monitor using micro HDMI cable
sudo apt install xfce4

TFTP installed and data trafer host to target system using TFTPbeagal bone login using Ssh by host system and able to data transfer by host system

ISSUE#1 - unable to run scp or ssh command on beagal bone board
sudo scp niranjan@192.168.29.155:/home/niranjan/project/02.RaspberryPi/source/linux/README ./
ssh: connect to host 192.168.29.155 port 22: Connection refused

ttyACM0 console not working in kernel 6.1.80 but able login prompt over ttyACM0 console in kernel 4,14

ramandeepwalia1994

iam building kernel which below option we have to chose?

make -j 4

SYNC include/config/auto.conf.cmd

*

* Restart config...

*

* General setup

*

Compile also drivers which will not load (COMPILE_TEST) [N/y/?] n

Compile the kernel with warnings as errors (WERROR) [N/y/?] n

Local version - append to kernel release (LOCALVERSION) [-v8] -v8

Automatically append version information to the version string (LOCALVERSION_AUTO) [N/y/?] n

Build ID Salt (BUILD_SALT) []

Kernel compression mode

> 1. Gzip (KERNEL_GZIP) (NEW)

2. Bzip2 (KERNEL_BZIP2) (NEW)

3. LZMA (KERNEL_LZMA) (NEW)

4. XZ (KERNEL_XZ) (NEW)

5. LZO (KERNEL_LZO) (NEW)

6. LZ4 (KERNEL_LZ4) (NEW)

7. ZSTD (KERNEL_ZSTD) (NEW)

choice[1-7?]:

raj.kiran

Hello everyone,

I'm currently working on a project with a Raspberry Pi 3B and using a Linux Mint host system. I've successfully cloned the GNU toolchain and set the path to it. I am able to configure and build the kernel image without any issues. However, I encounter problems when trying to build U-Boot with the same compiler.

cc1: warning: unknown register name: x18
{standard input}: Assembler messages:
{standard input}:37: Error: unexpected character `n' in type specifier
{standard input}:37: Error: bad instruction `b.ne 1b'
make[1]: *** [scripts/Makefile.build:257: arch/arm/cpu/armv8/cpu.o] Error 1
make: *** [Makefile:1892: arch/arm/cpu/armv8] Error 2

Has anyone encountered a similar issue or can provide some guidance on how to resolve this? Any help would be greatly appreciated.

Thank you!

chandhanif

To get the kernel source please use following command:

git clone --depth=1 https://github.com/raspberrypi/linux.git

The document has git clone --depth=1 https://gitlab.com/raspberrypi/linux. It will ask for the Gitlab ID.

009.08.Board Bringup. Paspberry Pi4

Howdy, Stranger!

Categories